1100-1150 and 1200 GS throttle lock/cruise control

Mine arrived last friday :thumb2, so fitting this week after Exams :tears etc.
Ta fer that.
 
Just ordered for an 07 GSA (both ends)

Being a bit thick here, but how does it work ? :confused::confused:
 
its all in the friction

AlanL said:
Just ordered for an 07 GSA (both ends)

Being a bit thick here, but how does it work ? :confused::confused:
Click to expand...

No, not a bit thick :augie
:rob
When it arrives it will all be obvious, just fitted mine this morning before going out to play.
Torx 55 key to undo the existing bar ends, replace with shite an briney new ones, job done!
RHS has an externally knurled, internally threaded ring which pushes a nylon spacer against the throttle tube and holds it open at whatever version of open you happen to be using.
LHS has......
 
Last edited:
Just ordered

Jaws

Just placed an order on your site and paid by Paypal. Didnt however get the opportunity to entermy UKGSer name!

Thx

Steve
 
Hi just ordered a throttle lock for my 1200 but didn`t get a chance to enter my site user name paypal payment was from paulgarner42.
 
SOmeone has suggested I start doing a rear wheel location tool thing.
Basically a bit of stainless with the wheel stud thread on one end and an alan key socket on tother..
You can screw it in to a wheel bolt hole and plop the rear wheel on.. The stud will hold it in place while you put the others bolts in.. Then undo the locator and fit the last bolt..
Proly only be a few quidlets but wondered if there was any interest before I run a bar off ?
 
ordered 1150 bar risers :bow
chads fault :blast
 
Jaws said:
SOmeone has suggested I start doing a rear wheel location tool thing.
Basically a bit of stainless with the wheel stud thread on one end and an alan key socket on tother..
You can screw it in to a wheel bolt hole and plop the rear wheel on.. The stud will hold it in place while you put the others bolts in.. Then undo the locator and fit the last bolt..
Proly only be a few quidlets but wondered if there was any interest before I run a bar off ?
Click to expand...

If it was reassuringly cheap I'd be interested ;)

Would it need the hex socket? - how about a couple of flats on it so you could grip it and spin it in by hand?
 
mike wright said:
There perfectly finished and a top job at a fraction of the TT price :thumb2 .... Made a massive difference to comfort on mine
Click to expand...

got the wunderlich units on at the mo,but the jaws units are higher.:thumb
 
Jaws said:
SOmeone has suggested I start doing a rear wheel location tool thing.
Basically a bit of stainless with the wheel stud thread on one end and an alan key socket on tother..
You can screw it in to a wheel bolt hole and plop the rear wheel on.. The stud will hold it in place while you put the others bolts in.. Then undo the locator and fit the last bolt..
Proly only be a few quidlets but wondered if there was any interest before I run a bar off ?
Click to expand...

HI John,
yes and yes -as you know, I want a set asap please -going away end of June ! I have the rear wheel off now, so would have been useful today- got the slow puncture on the route to Banham, it was a leaky valve though.
Despite what Steptoe says, that rear 1150 wheel is a pain to re-locate onto the shaft :roll.

cheers,
Roger
 
wheel locator

Roger Chatterton said:
HI John,
yes and yes -as you know, I want a set asap please -going away end of June ! I have the rear wheel off now, so would have been useful today- got the slow puncture on the route to Banham, it was a leaky valve though.
Despite what Steptoe says, that rear 1150 wheel is a pain to re-locate onto the shaft :roll.

cheers,
Roger
Click to expand...

I'll have one too please Mr Jaws. was going to make my own somehow but if your knocking them out then I'll have one please also asap as will also be off in three weks.
Dave GS.
 
I have just fitted my up and back risers too, It took me five minutes tops, it feels good, Cheers Jaws :thumb2
I just need an excuse to go somewhere, I think I left a tentpeg in Ullapool :)

Stewart
 
Stewart H said:
I have just fitted my up and back risers too, It took me five minutes tops, it feels good, Cheers Jaws :thumb2
I just need an excuse to go somewhere, I think I left a tentpeg in Ullapool :)

Stewart
Click to expand...

I just got some of those from Jaws too :thumb2

They feel good while stationary but I've not had a chance to try them on the road yet - looking forward to a spin.
 
Nippy Normans supply Touratech, Wunderlich, Desert Fox and many other makes of accessories.
You must log in or register to reply here.

Similar threads

Official weights of 1100, 1150 and 1200?
Replies
6
Views
4,474
Jimb


Back
Top Bottom