Bronze metal in the engine oil

dashfixer

Active member
UKGSer Subscriber
Joined
Dec 28, 2011
Messages
235
Reaction score
47
Location
Worcestershire
I have just drained the engine oil as part of a service on my 09 1200GS and found what looks like bronze filings in the oil. Gold coloured and non-magnetic there are quite a lot of them.
I'm wondering where it has come from, my guess is shell bearings, either big ends or crank main bearings.
Anywhere else? Has anyone experienced this and if they have what was the source?
The bike has done 91k miles.
 
In October you were wanting to change the cam chain tensioners, IIRC. If you had been having issues with one or more tensioners then a flapping cam chain would accelerate the wear of both chain and the slippers. You could be looking at material worn from the slipper assembly.
I did a full strip and rebuild at 140,000 miles, because I had stripped the frame off for repainting. The big end shells were barely worn, nor the cam chains. I replaced them anyway, along with the 2 slipper blades whose common pin is held between the crankcase halves.
Unless you have had oil supply issues or been running without enough oiI would check your chain tensioner blades, especially since you had tensioner issues.
 
In October you were wanting to change the cam chain tensioners, IIRC. If you had been having issues with one or more tensioners then a flapping cam chain would accelerate the wear of both chain and the slippers. You could be looking at material worn from the slipper assembly.
I did a full strip and rebuild at 140,000 miles, because I had stripped the frame off for repainting. The big end shells were barely worn, nor the cam chains. I replaced them anyway, along with the 2 slipper blades whose common pin is held between the crankcase halves.
Unless you have had oil supply issues or been running without enough oiI would check your chain tensioner blades, especially since you had tensioner issues.
I thought that the bike had a bit of a rattle when it was hot. I've just done a top end strip down and had a look at cam chains, tensioners, guide blades, big end shells, and also timing gears, timing chain, tensioner and oil pump. There is virtually no sign of wear on anything, also no sign of metal particles in quiet areas of the engine. Most of the engine components look like they have just been made.
There's no issue with the oil supply or level, I cut the old filter open and checked in side, nothing. I'm baffled at where the metal particles have come from and why there's nothing in the filter.
I'm now happy to continue riding and just monitor the bike. I'm not sure if I was becoming paranoid and imagining the rattle.
 
Last edited:
How did you manage too look at the big end shells
with just a top end strip down..?
i would have thought if both top-ends are off , you can get to the big ends.
pictures of shells needed .
does a BM crank pull up on the front sprocket ??? if so , thrust bearing at the front ?
@Steptoe , calling Steptoe.
 
i would have thought if both top-ends are off , you can get to the big ends.
pictures of shells needed .
does a BM crank pull up on the front sprocket ??? if so , thrust bearing at the front ?
@Steptoe , calling Steptoe.

When he says top end strip down I presume he means cylinder head and parts attached … barrels and pistons still in place so you can’t see into the crankcase…
 
How did you manage too look at the big end shells
with just a top end strip down..?
Because I took the con rods off. I have always thought of the top end being down to the crank cases. So heads, barrels, pistons and con rods were removed. The big end shells are in good condition. There is no sign of metal in the crankcase including in the residual oil in the quiet areas.
 
Just a thought. Are you certain you're seeing metal? Could they be plastic fragments? Not sure what it could be, but based on things looking ok, maybe it's something else? The tensioner a meeting above?
 


Back
Top Bottom