Sorry they're Mitas E-09's - the E standing for Enduro
Should have looked at them before posting
Many thanks
G650 XCountry - Hepco & Becker Centrestand fitted
- Thread starter JohnnyBoxer
- Start date
Many thanks
Thanks for the heads up JB ... fitted mine today 
Had to modify the BMW engine bars a little, no great deal ... the centre stand looks almost a continuation of them
Fit great, look good, great mod
Yes ... I know it's dirty
Had to modify the BMW engine bars a little, no great deal ... the centre stand looks almost a continuation of them
Fit great, look good, great mod
Yes ... I know it's dirty
That ticks so many boxes I'm inclined to draw a few more so I can tick them.
Looks good Mick
Glad you're pleased with it, saves a load of hassle when maintainng the bike and best of all, it's OEM quality/fit
If you want some conduit trunking for the middle bar, send me a PM
Glad you're pleased with it, saves a load of hassle when maintainng the bike and best of all, it's OEM quality/fit
If you want some conduit trunking for the middle bar, send me a PM
Where the engine bars are mounted with a plate between the footrest mounting and the frame, they have a bit if an 'L' shaped bracket underneath, for strength I guess, just had to hacksaw
part of it away, then file and tidy up, so as to make room. Sounds complicated but you'll see when you come to fit The bolts supplied with the centre stand are long enough to allow for the engine bars plate being sandwiched between
As JB has said, the H&B stand looks like BMW original, had they fitted one
H&B don't supply a centre stand for the later post 2007 lower models
Hope this helps
Quick edit for Nutty ...
You can see here where the centre stand main chunky bracket fits behind the engine bar plate (the centre stand brackets have to be next to the frame) the engine bar plate has some steel bracketing that has to be relieved
Attachments
Where the engine bars are mounted with a plate between the footrest mounting and the frame, they have a bit if an 'L' shaped bracket underneath, for strength I guess, just had to hacksaw
The bolts supplied with the centre stand are long enough to allow for the engine bars plate being sandwiched between
As JB has said, the H&B stand looks like BMW original, had they fitted one
H&B don't supply a centre stand for the later post 2007 lower models
Hope this helps
Quick edit for Nutty ...
You can see here where the centre stand main chunky bracket fits behind the engine bar plate (the centre stand brackets have to be next to the frame) the engine bar plate has some steel bracketing that has to be relieved
Thanks Micky.
Fitted mine today to the XCh. Doesn't have the 'pedal' like the XCo ones above but works and looks great
Didn't know they did them for the Xchallenge
Can you stick a couple of piccies on? I'm thinking there might be one or two on here that might be wanting to fit one
Didn't know they did them for the Xchallenge
Can you stick a couple of piccies on? I'm thinking there might be one or two on here that might be wanting to fit one
Sure, was planning to when my project is finished (at this rate in about 5 years time
).
I had a foot welded on to mine to make it easier. I'll take some pictures when I'm home.
Or you could could save weight, money, ground clearance lifts either front or rear wheel and can be used the same one on several bikes
Same idea here, kick it straight and the wheel is up off the ground
Works a treat, stable and cheap
Mine or Tim's?
Home made, works just fine. No substitute for a proper main stand of course ...
Mine or Tim's?
Home made, works just fine. No substitute for a proper main stand of course ...
Yes, yours! Nice job...
I like the idea of those but didn't have any channel around when I knocked this one up for use on the TATSame idea here, kick it straight and the wheel is up off the ground
Didn't know they did them for the Xchallenge
Can you stick a couple of piccies on? I'm thinking there might be one or two on here that might be wanting to fit one
Here you go:
Attachments
I like the idea of those but didn't have any channel around when I knocked this one up for use on the TAT
I didn't either, so made the channel sections up
Looks good
