Innovv - camera systems where did

[Santa-2512]

You mount the control box and cameras??

Just trying to fit a K2 to the hexhead


I've got the rear camera sorted & possibly the control box thing & PSU

The front camera is a tad more difficult - lots of locatoions & lots of problems

What did you peeps do ?

 

[richard shaw]

Just on the right hand side as you look at the picture, hope this helps


Sent from my iPhone using Tapatalk

 

[richard shaw]

Sent from my iPhone using Tapatalk

 

[chablis]

Can't speak from experience, but I thought I recalled a bracket, I see Innovv do on for a 1250,

Have a look at

https://www.advrider.com/f/threads/innov-k2-dash-cam-install.1442479/

 

[Santa-2512]

View attachment 340585
Just on the right hand side as you look at the picture, hope this helps


Sent from my iPhone using Tapatalk

Looked at doing that - how did you fix the camera ?

 

[richard shaw]

Looked at doing that - how did you fix the camera ?

The bolt that holds the oil cooler to the frame I swapped it for a longer one then mounted the camera to it with a m6 nut


Sent from my iPhone using Tapatalk

 

[Mistacat]

Mounted mine in a similar place except it is a little further forward due to the protective Perspex cover.
Used a protective cover as the plastic on the Chinese headlight does not feel very strong , already had a stone crack one cover but made 3 out of £8 worth of Perspex so disposable.
The Camera bracket I made is a copy of the one in the kit with less offset.

 

[Pukmeister]

I'm seriously tempted by a front/rear motorcycle 'dashcams' for both my bikes, its just the price/performance that I need to work out.

My GSA is an expensive investment worth protecting.

My daily commute on my old cheap Tmax is almost a fight for survival through the traffic.

 

[richard shaw]

This is where I mount the rear camera, a bit off messing around but worth it


Sent from my iPhone using Tapatalk

 

[Headtester]

Mounted mine in a similar place except it is a little further forward due to the protective Perspex cover.
Used a protective cover as the plastic on the Chinese headlight does not feel very strong , already had a stone crack one cover but made 3 out of £8 worth of Perspex so disposable.
The Camera bracket I made is a copy of the one in the kit with less offset.

Where did you get your perpex cover from please? I've go the same / similar headlight and need to use (or blank off) the holes in each corner of the light

 

[Bigcats]

I'm seriously tempted by a front/rear motorcycle 'dashcams' for both my bikes, its just the price/performance that I need to work out.

My GSA is an expensive investment worth protecting.

My daily commute on my old cheap Tmax is almost a fight for survival through the traffic.

I keep looking as well

The K7 from innovv is what I keep going back too

maybe we could get a discount for buying two??

(plenty of 5% etc for these on youtubers comments)

 

[Pukmeister]

Expensive though for 2k.

I probably only need 1080P to provide insurance footage as proof of blame in the event of an accident unless it is a hit and run.

Plenty of 1080P stuff on Amazon etc for about £100 per kit.

I'm tempted to try one of these on the Tmax:

Amazon.co.uk

 

[Bigcats]

Expensive though for 2k.

I probably only need 1080P to provide insurance footage as proof of blame in the event of an accident unless it is a hit and run.

Plenty of 1080P stuff on Amazon etc for about £100 per kit.

I'm tempted to try one of these on the Tmax:

Amazon.co.uk

certainly gets good reviews

 

[Santa-2512]

The bolt that holds the oil cooler to the frame I swapped it for a longer one then mounted the camera to it with a m6 nut


Sent from my iPhone using Tapatalk

TA

where did you mount the

This is where I mount the rear camera, a bit off messing around but worth it


Sent from my iPhone using Tapatalk

I looked at going central, but there is a fixing there that looks interesting thank you ,

 

[Mistacat]

Where did you get your perpex cover from please? I've go the same / similar headlight and need to use (or blank off) the holes in each corner of the light

The piece of Perspex was from ebay and the M5 threaded rubber inserts I had in the workshop along with the nylon 66 to make the spacers.
I seem to recollect someone on this forum was making kits to order , perhaps someone else may remember.

 

[Mistacat]

I put my rear camera next to the Innovv third eye just below the extra brake and tail lights ( Chinese on home made bracket) below the top box.
I put the control / led unit inside the hand guard as no room on the Handlebars as have too many toys fitted.

 

[Pukmeister]

I've decided to test the water with a cheap 1080P dual bike "dashcam" from Aliexpress for a mere £70, same item as the ones sold on Amazon with decent reviews for £100 plus.

I'll bolt it onto my Tmax for the daily commute, at least I should have some video if I ever get knocked off in traffic.

The Innovv stuff looks decent enough quality but IMO its too expensive for what it is, plus I'm a sceptic when I see so many YouTubers/Influencers bigging them up when other brands are also available: They seem to be aggressively marketed at the motorcyclist.

 

[Mistacat]

I had an Innovv C1 and C3 For many years on my old GS . recently fitted the K3 so put the c3 on my airhead and the C1 on my pickup.
The old cameras have done 100k miles so decided to semi retire them.
The build quality of these newer Innovv systems are far better than the earlier ones so hoping they will outlast my needs.

 

[Udders]

Front camera

Rear camera

Obviously this is the vastly superior 1150 though.

 

[dicktheleg]

Here’s mine on my TC