Has anyone fitted any, with or without the luggage, and if so please share a photo/description.
Thanks.
Thanks.
Additional Rear Brake Lights
- Thread starter developer
- Start date
Not LC. I will admit, but I have a set of rear indicator / stop lamps fitted to my hexhead
Sent from my Nexus 7 using Tapatalk
Sent from my Nexus 7 using Tapatalk
Got a set of these from here....https://www.amazon.co.uk/gp/product/B00LEQ8JO8/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 which i then stuck to the top box (left and right side in vertical position) and wired in to my HEX EZcan (www.hexezcan.com). works with the brake light and will flash 3 times when braking before staying on constant. Of course, if you don't have the EZcan, then it could just take a feed from the brake light loom.
Hope this helps.
Thanks both - I think it would be good to upgrade from the single brake light, however, it has to look good and function properly.
Yep me.
Cost £1.50 per side and linked to the ExCan.
Off is at 10% light power. On is at 100% light power. So they act as side lights as well.
They are not the highest quality items and probably will need swapping over every now and then. But can't complain at £1.50
Two of my other GSA mates have fitted these and they look really good. Make the back end of the bike seem bigger.
Cost £1.50 per side and linked to the ExCan.
Off is at 10% light power. On is at 100% light power. So they act as side lights as well.
They are not the highest quality items and probably will need swapping over every now and then. But can't complain at £1.50
Two of my other GSA mates have fitted these and they look really good. Make the back end of the bike seem bigger.
Attachments
rear brake light additons
Also got the same set up as warlord, on the ezcan. I've had a few other bikes and mates asking how and where fitted.
The initial flicker and flash when you apply the brake attracts the eye, which can only be a good thing.
Also got the same set up as warlord, on the ezcan. I've had a few other bikes and mates asking how and where fitted.
The initial flicker and flash when you apply the brake attracts the eye, which can only be a good thing.
Also got the same set up as warlord, on the ezcan. I've had a few other bikes and mates asking how and where fitted.
The initial flicker and flash when you apply the brake attracts the eye, which can only be a good thing.
They work well don't they
I've got a set of Skene P3 lights. They are fitted to my LC RT and work fine without any EZ Can, just taped into the wiring and ok with the Canbus. Check their site for fitting to a GS. Very good company, US based, you would have to import them.
Hmm, Benhams - that's where mine is coming from - good guys
alex789
Registered user
I too have a set of Skene P3 lights, wired into the hex. 
Thanks - there's quite a few Skene installations on YT - I'd not heard of them until this thread.
mcinlb
Registered user
Good to hear that the Skene lights tap into the standard rear light without canbus issues, not all do. I bought an LED rear light and when I tapped into the wiring the canbus showed it as a fault. - Wired it through this - https://www.aliexpress.com/item/12V...695201931.html?spm=2114.search0104.0.0.9b3js3 .
Canbus does not see it and my light works ok fixed to my topbox.
The Skene lights are v expensive
Canbus does not see it and my light works ok fixed to my topbox.
The Skene lights are v expensive
Last edited:
On the Skene site they show various installations and how to wire them up. Skene are very good and stand by their own products. I had no issues putting them onto my RT LC, installation was very straight forward. But I bought mine before the pound devalued, so now I expect they are a bit more expensive.
woody1707
Registered user
Hi Andy B you don't know if this is Can Bus compatible do you. I like the look of this but don't have a Hez ExCan and don't really want to go to the expense as I have few other accessories .
Cheers
transalper44
Registered user
Anyone fitted indicators to sides of their panniers ? Been mentioned by riding mates that at certain angles, the bike indicators can't be seen due to the panniers. If so, photos etc would be appreciated .
woody1707
Registered user
Just in case anyone else was wondering I have emailed the manufacturer and they have confirmed that these are not Can Bus compatible.
Hi Developer,
I have a 2016 GS TE and I fitted a set of these connected in to my HEX Ez CAN so I can set a % of normal rear light and Brake light.
https://www.bikevis.com/product/bikevis-bullets-v2-motorcycle-running-lights/
I have just spotted this so you can use them as I have without the expense of buying a HEX Ez CAN:
https://www.bikevis.com/product/bikevis-motorcycle-tail-brake-converter/
Will go take a couple of pictures for you.......back in a minute
Right I'm back:
Rear Lights
Brake Lights with the help of my trusty assistant
I have a 2016 GS TE and I fitted a set of these connected in to my HEX Ez CAN so I can set a % of normal rear light and Brake light.
https://www.bikevis.com/product/bikevis-bullets-v2-motorcycle-running-lights/
I have just spotted this so you can use them as I have without the expense of buying a HEX Ez CAN:
https://www.bikevis.com/product/bikevis-motorcycle-tail-brake-converter/
Will go take a couple of pictures for you.......back in a minute
Right I'm back:
Rear Lights
Brake Lights with the help of my trusty assistant
Camel Toe
Registered user
Bike show in a few days chaps......sure to be options there.....
Similar threads
