GSA Tobinators. Help!

[pbboxer]

Hi
Ive got GSA se and I recenty bought a second hand tobinators kit from a chap on here. It's an adventure kit.
Does anyone have any instructions at all please? I spent about 30 mins last night messing about and gave up. Cant figure it out!

Any help appreciated please

PB

 

[Voyager]

Hi
Ive got GSA se and I recenty bought a second hand tobinators kit from a chap on here. It's an adventure kit.
Does anyone have any instructions at all please? I spent about 30 mins last night messing about and gave up. Cant figure it out!

Any help appreciated please

PB

I'll scan the instructions and post them here in a little while.

Bob.

 

[pbboxer]

Thanks very much

PB

 

[Voyager]

I'll scan the instructions and post them here in a little while.

Bob.

Here you go, I hope you can read them.

Pay particular attention to Note 14 - I didn't think I'd overtightened mine but after six months use I started to get cracks on both sides of the screen. I drilled 1.5mm holes in the end of each crack to prevent them spreading.

Best of luck . . you can now spend the rest of your life seeking the "sweet spot"

(Thanks to Andrew Tobin - I hope he doesn't mind me doing this )

Bob.

 

[Voyager]

I just noticed . . I could have just given you the download link





Bob.

 

[pbboxer]

Top man, thanks very much.
The centres on my bike look to be different somewhow, will have a gander later. Ta

PB

 

[pbboxer]

Well i'll be buggerred if I can see what to do next, other than have to go out and buy some spacers etc.
I removed the big wedges from the bike, fitted the tobinators as per insructions, yet i can't see how they'll fit. I admit fully to being mechanically inept to a degree but its bobvious here there needs to be some sort of spoacers or a smaller "wedge" put in where te original was. Will take pics ... feeling a bt daft here.
Theres approx a 20mm gap to the holes from the front hole and about 25 to the rear. The tobinator at the front look extremely close to the plastic above the headlight too

 

[pbboxer]

http://www.putfile.com/pic/7896177

http://www.putfile.com/pic/7896174

http://www.putfile.com/pic/7896175

http://www.putfile.com/pic/7896176

 

[vireo]

PB

As far as I can see you need the adventure adaptors Nippy Norman (see link at top of page) Item Number : TOB-1150GSAA

These go in to the space shown in your image http://www.putfile.com/pic/7896174 and you then attach the assembled screen plus tobinator bits to it as shown (photographed looking up from below) in the attached - worked for me!

Vireo

 

[pbboxer]

Thanks mate
I was sold a GSA tobinator kit second hand on here and obviously inccorrectly assumed Id get the whole lot i needed!
How silly of me

 

[pbboxer]

Sorry to ask, but is there any possibility you could measure th depth of te bits im missing please? Ie at each end so I know what sizezd spacer to stick in there as a temp measure until i can get ohold of the proper item? Would be much appreciated is poss. Thanks a lot

PB

 

[vireo]

Sorry to ask, but is there any possibility you could measure th depth of te bits im missing please? Ie at each end so I know what sizezd spacer to stick in there as a temp measure until i can get ohold of the proper item? Would be much appreciated is poss. Thanks a lot

PB

Hi PB

See attached which might assist you in making up the bit you need (TBH, you're probaly best stump up the £30 for new one's if you can afford it). The other critical measurement is the gap between the mounting points, but you can measure these easily.

Note that a section of the dash on the LHS (sitting on bike) will foul the adaptor at the thicker end if there's not a small section cut out of it.

Vireo

 

[pbboxer]

fantastic, many thanks indeed