Multi purpose rear indicators- wiring diagram
- Thread starter Bob Jeffries
- Start date
Following that too.
www.gs-forum.eu
But (for now) they are messing up with relais and cutting wires. But by looking at the video it seems it can be done by programming. And for the same price as the weiser sets you have the gs911 AND the Indictators you want.
Blinker update hinten Bj. 2021
OK. Das wusste ich nicht. Ich dachte, das sei Serie ab MJ 21. Ist Teil des Lichtpakets. Wobei ich nicht verstanden habe, was neben dem hier diskutierten unerwünschten Verhalten der Blinker noch dazu gehört
But (for now) they are messing up with relais and cutting wires. But by looking at the video it seems it can be done by programming. And for the same price as the weiser sets you have the gs911 AND the Indictators you want.
Victor c
Registered user
I’m sure I’ve read, or seen a YouTube vid, that BMW dealers can code the 2021 onwards bikes indicators and tail lights to act like the previous version. If they can do it, then it will hopefully be possible via Hex GS 911 in a future update.Following that too.
Blinker update hinten Bj. 2021
OK. Das wusste ich nicht. Ich dachte, das sei Serie ab MJ 21. Ist Teil des Lichtpakets. Wobei ich nicht verstanden habe, was neben dem hier diskutierten unerwünschten Verhalten der Blinker noch dazu gehört
But (for now) they are messing up with relais and cutting wires. But by looking at the video it seems it can be done by programming. And for the same price as the weiser sets you have the gs911 AND the Indictators you want.
That was said in a YT vid. They said you had to go to BMW and a guy from the dealership could change of modify your details in the main (german) BMW Computer. Otherwise, so was said, after an update from the mainframe the changes where lost.
Gutted I bought the Weiser Wizards as soon as I bought the bike in October. The majority crowd I ride with commented after my first ride with non Wizard mod.
They all said the Wizard mod was a definite improvement.
New Topic; if I bought some Denali lights could I just wire them in, in place of the BMW lights without the Denali controller. IE take the wires off the BMW lights and connect to the Denali
They all said the Wizard mod was a definite improvement.
New Topic; if I bought some Denali lights could I just wire them in, in place of the BMW lights without the Denali controller. IE take the wires off the BMW lights and connect to the Denali
Sorry should have said fog/spotlights
Looking at Weiser Wizards they are charging for plug and play hardware that the GS-911 delivers all but one of the items of functionality :
- The Front indicator modules when installed cancel out the “always on” low level amber day/nighttime running lights. The indicators activate as normal when required. Clearly and with no ambiguity. GS-911 will do this
- The Rear indicator modules function normally as both red running and brake lights until the indicator is activated. When an indicator is activated (on either side) the module cancels out both the running and brake lights leaving only the amber indicator light clearly visible on that side. There is no longer any confusion or ambiguity for following traffic of the rider’s intentions. GS-911 on my bike (2022 GSA) will not do this and I am in discussions/ testing beta software with Hex Innovate to see if they can resolve it
- The Rear taillight module reactivates* the missing main rear running light function adding needed conspicuity. This extra lighting is vital when competing to get noticed in today’s traffic conditions and complements the re-sequenced rear indicator functionality. GS-911 will do this
Victor c
Registered user
I wait with bated breath, for the next software update release
On my old 21 plate GSA I fitted a set of T3’s to my rear number plate which were possi tapped (not sure on spelling) onto the OEM rear indicator wiring. Worked brilliantly with only one small issue. If I had the emergency stop I would get a rear break light failure message on the tft. Lights still functioned property with no loss of function and turning the bike on and off cleared the fault message. This might have been down to my fitting though. T3’s come with canbus connector and possi tap so you can choose.
Aussie Jack
Registered user
Multi-function Rear Turn Lights
Hi All,
Finally got it done after a false start.
This will fit any pre-Multi turn bike, and can be done for aroun $100.
Hi All,
Finally got it done after a false start.
This will fit any pre-Multi turn bike, and can be done for aroun $100.
Similar threads
