New Project Coming.....

Well it's here , not to everyones taste but I really like them having had a few of them over the years

Seems way better than advertised , once I fitted a new battery it fired straight up and everything works on it other than the EHCS centre stand , but that appears to be just a hydraulic seal issue as it's leaking oil from around the actuator shaft area and the motor is spinning

Someone has fitted the wrong tyres as it has radials on it and because of the weight of the bike it should have bias ply . I would have been changing them anyway as they are pretty worn and dated 2021

Previous owner had paid over £2000 in 2022 to have the iABS pump replaced for a new one as the invoice is in the service history file , I think I would have just done an ABS bypass but the servo brakes for the moment are working really well so I will have to decide if I de ABS or not . I will be changing the brake hoses to SS braided lines and refurbishing the calipers anyway

So for now just a full service and ride it and then decide what if anything else to do to it . So its not really the next project bike which means I can now concentrate on the Moto Guzzi le Mans re-commission

I'll post a few updates as I service the K and rebuild the EHCS centre stand actuator

View attachment 549733
Question regarding ABS, I am aware of issues with brake servos on these early bikes, would a later ABS module work as a replacement, one from a K1300s perhaps? Which I believe are less problematic.
 
Question regarding ABS, I am aware of issues with brake servos on these early bikes, would a later ABS module work as a replacement, one from a K1300s perhaps? Which I believe are less problematic.

The electrics would be the challenge and no one I’m aware of has done it


Sent from my iPhone using Tapatalk
 
  • Like
Reactions: HxH
Thought perhaps a straight swap, but as you mention electronics a bit tricky, I know I had a swap done on a Kawasaki GTR1400 2007 with duff ABS module, swapped with a working GTR1400 2011 module.
Work was carried out by a Motorcycle Mechanic.

Unfortunate, they do not have the same on newer models of BMW K1200LT (discontinued) or perhaps a newer BMW R1200RT.
 
Last edited:
Bike now de-ABS'd , pump and pipework removed , blue ABS relay pulled and the brown/red & brown/yellow wires snipped to remove the brake failure warning light on the dash

New Venhill SS braided lines arrived and new Metzler Marathon Ultra M888 tyres fitted (forgot how expensive these tyres are !)

IMG_1117.jpegIMG_1118.jpegIMG_1119.jpegIMG_1120.jpegIMG_1121.jpeg
 
I have had a similar thought on the top box , riders in USA have used a Harley rear rack to replace the top box , I have to draw the line with foot boards though , definitely not for me

View attachment 548897
Cracking work as ever. I’ve never imagined one of these without the huge top box, but this gives the bike a whole new look. I like it.
 
Must be a good 10-15kgs weight saving, without that lump of an abs module. Doubt you will notice any difference while riding though. (y)
 
  • Like
Reactions: KMD
Evening love these old bikes

Will it be for sale as I’m interested if so ?
 
One last issue to resolve on the big K , final drive oil was black and when I removed the fifth central wheel bolt oil dripped out . After a chat with Mikeyboy and DrFarkoff issue was pinned down to the aluminium cone piece that is shrunk fit onto the crown wheel being loose . Time to phone a friend and Da1sycat to the rescue with a spare final drive that I included when I sold him my K1200LT back in 2019

IMG_1129.jpegIMG_1130.jpeg
 
I had a K1200RS for a few years. Lovely bike and an amazing smooth and torquey engine.

However, that bodywork.... ANY job was a whole day in the garage, mostly trying to get the panels to line up when putting it all back together. I can only imagine the LT is five times worse!
 
Replacement final drive all stripped ready for fitting new bearings which I hopefully get tomorrow

IMG_1162.jpeg

ABS controller wiring all tided up and boxed in

IMG_1163.jpeg


IMG_1165.jpeg

Also cleaned and fitted new seals to the gear change linkages

Hard brake lines fitted

IMG_1142.jpeg

IMG_1144.jpeg
 
As someone with the mechanical skills of a lettuce, I’m in awe. Bravo 😎
 
That’s tomorrows job sorted

9977d28e31d5b2e3b70b8a655614523e.jpg



Sent from my iPhone using Tapatalk
 
Final drive back on bike , get the brakes bled tomorrow and the wheels back on then just the tupperware to screw back on

IMG_1181.jpeg
 


Back
Top Bottom