Swingarm bearings

Danny996

Member
UKGSer Subscriber
Joined
Oct 8, 2024
Messages
23
Reaction score
2
Location
Eastbourne
I’ve ordered two Swingarm bearings, gearbox end, from motorworks. I thought they’d be bmw but are FAD. Do these require packing with bearing grease prior to fitting? If yes, do I pack both sides? I’ve not packed bearings before, but I presume I pop the outer seal off and pack it full - or half full then pop the seal back on?
I’ve removed my rusty bearings and like an idiot I didn’t make a note of which was the inner/outer side. Which is the inner ( facing into swingarm )?
 

Attachments

  • IMG_3553.jpg
    IMG_3553.jpg
    48.3 KB · Views: 37
  • IMG_3552.jpg
    IMG_3552.jpg
    49.1 KB · Views: 38
I did mine last winter and did put extra grease on them, carefully pop the seal out, add grease, replace seal. The seals do bend out of shape very easily.
This might not be the definitive answer but I always add a bit more grease to bearings, I believe the factory put in the bare minimum.
As to which way round, the general rule is the side with the writing, serial numbers etc, faces outwards.
 
Great, thanks for replying. I’ll pack them prior to fitting. Now I’ve looked at the photos again, I’m pretty sure the black seal ( with the thinner rim ) is the outer face.
 
Great, thanks for replying. I’ll pack them prior to fitting. Now I’ve looked at the photos again, I’m pretty sure the black seal ( with the thinner rim ) is the outer face.
I've found the pics I took at the time I did mine, with the remains of the bearings still attached to the bearing removal tool.
They are taper roller bearings, and looking at the orientation of the tool, the wider part of the taper is on the outside.
Yes, they really were that bad, and it had passed the MOT a few weeks, less than 10 miles, previously!
 

Attachments

  • IMG_20260203_141749_060.jpg
    IMG_20260203_141749_060.jpg
    135.4 KB · Views: 34
  • IMG_20260203_142203_967.jpg
    IMG_20260203_142203_967.jpg
    98.3 KB · Views: 34
  • Like
Reactions: MWH
Why disturb the seal😳🫣? The swinging arm only moves up and down slightly and nowhere near the amount of movement the bearings are designed for, breaking the seal could allow water etc to get in and rust them. In 25 years of rebuilding alternators that are constantly rotating for millions of revolutions during their life I have never added extra grease.
 
Very similar to mine. I’m changing the front boot as I think water has been creeping in over time and corroded everything. My bearings had rusted onto both the LHS and RHS pins. It was a complete nightmare doing this for the first time. Now I’ve done it once, the second time round won’t be so bad. Thank god for this forum and YouTube!
I’ll pop the bearings in the freezer and heat the swingarm holes with a heat gun which should make them easier to fit 🙏🏻
 
Why disturb the seal😳🫣? The swinging arm only moves up and down slightly and nowhere near the amount of movement the bearings are designed for, breaking the seal could allow water etc to get in and rust them. In 25 years of rebuilding alternators that are constantly rotating for millions of revolutions during their life I have never added extra grease.
Ah ok. Maybe I’ll just fit them as they are and check them again next year when I recheck the final drive.
 
They are greased from the factory at FAG. No need to add more, you can overfill bearings with too much grease.

If you really want to add grease, leave the seal in place. Fill from the back as these are only sealed on one side.
 
Why disturb the seal😳🫣? The swinging arm only moves up and down slightly and nowhere near the amount of movement the bearings are designed for, breaking the seal could allow water etc to get in and rust them. In 25 years of rebuilding alternators that are constantly rotating for millions of revolutions during their life I have never added extra grease.
For sealed bearings you are right. Bearing manufacturers put just enough grease in to suit the intended life of the bearing.
That said, the swinging arm bearings are two piece taper rollers that do not rotate more than a few degrees. The grease does not distributed around the bearing faces by rotation. Before fitting, I packed mine with a waterproof grease, working it into the inner race. The thinking behind that is to protect the bearing from moisture and therfore from corrosion. The way these bearings are used there is no risk of harming the bearings by overpacking with grease.
TBH, self lubricating bushes, with thrust bearing faces would do the same job, maybe even last longer. BMW seens to have always done it this way though, every boxer twin I have had used taper roller swinging arm bearings.
 
I’ve ordered two Swingarm bearings, gearbox end, from motorworks. I thought they’d be bmw but are FAD. Do these require packing with bearing grease prior to fitting? If yes, do I pack both sides? I’ve not packed bearings before, but I presume I pop the outer seal off and pack it full - or half full then pop the seal back on?
I’ve removed my rusty bearings and like an idiot I didn’t make a note of which was the inner/outer side. Which is the inner ( facing into swingarm )?
The side with the larger diameter centre race faces out. When the tensioner is screwed in on the left hand pivot it pushes the centre into the outer race to tighten the bearing. The manual will give you the exact tightening tirque for that pivit pin, do not confuse that with the tirque value for the lock nut. If you do, your swinging arm will likely not move.
BMW do not make much themselves, they mostly assemble parts made elsewhere. Bearings are a specialist part, there are not many manufacturures worldwide, FAG is one of the better brands.
 
The side with the larger diameter centre race faces out. When the tensioner is screwed in on the left hand pivot it pushes the centre into the outer race to tighten the bearing. The manual will give you the exact tightening tirque for that pivit pin, do not confuse that with the tirque value for the lock nut. If you do, your swinging arm will likely not move.
BMW do not make much themselves, they mostly assemble parts made elsewhere. Bearings are a specialist part, there are not many manufacturures worldwide, FAG is one of the better brands.
Great thanks. I bought the laser tool for the LHS so I can torque it properly and I’ll mark the inner pin with a dab of paint so I can make sure it hasn’t moved when tightening up the nut.
 
Great thanks. I bought the laser tool for the LHS so I can torque it properly and I’ll mark the inner pin with a dab of paint so I can make sure it hasn’t moved when tightening up the nut.
Yes I also marked mine on both sides with a dot of red paint to easily see if anything has moved. I've done the swing arm bearings on both my GS & RT (same design) and nothing has moved so far, and that's about 3-4 years ago. The bearings are specific to BMW, you can get taper roller bearings of the same size, but without seals. I found that the correct ones are only available from BMW specialists such as Moto Works.
 


Back
Top Bottom